Results 1 to 5 of 5
  1. #1

    Default New Tahitians and How to Clean Them?

    Hi everyone. I browse this forum constantly but post very rarely. I hope to change that!

    I recently bought some lovely Tahitian pearls and Vietnamese akoya pearls second hand from a lovely person and they are arriving today. She never strung them and bought them from Cees.

    In one of her emails she told me that she bought the pearls and they were freshly drilled right before they were sent to her. She did not clean them but strung them on a plastic cord to send them to me. She said I would probably want to clean the pearls as they have drilling residue inside of the holes still and I'm thinking some of this residue may be on the surface of the pearls as well. She recommended that I wash them using mild soap and water and to not let them sit in the water because in her experience with other pearls, when she let them sit for too long, the water and the drilling residue kind of bonded together and left a film on the pearls that was tricky to remove.

    How should I go about cleaning these pearls? Should I use water at all or should I just wipe them with a dampened paper towel? Or is there another method that is recommended? I have never had to deal with pearls that are freshly drilled and I have never purchased an unstrung strand of pearls before. I would greatly appreciate any advice!

    I attached an image that the seller took of the pearls. Name:  COMBO_2.jpg
Views: 140
Size:  14.7 KB

  2. #2
    Museum Pearl Senior Pearl-Guide.com Pearl Expert BWeaves's Avatar
    Join Date
    May 2015
    Location
    Orlando, Florida, USA
    Posts
    5,852

    Default

    I'd put a wash cloth at the bottom of the sink (to prevent the pearls banging on any hard surface). Then wash them with soap and water. Rinse them in clear water. Roll them in a towel and let them sit until the towel is dry. This prevents any water spots.

  3. #3
    Pearl Enthusiast Senior Pearl-Guide.com Pearl Expert Pearl Dreams's Avatar
    Join Date
    Sep 2007
    Location
    Connecticut
    Posts
    9,039

    Default

    They probably don't need to be washed, being new-- just wipe with a soft cloth dampened with bottled or filtered water. (Chlorine is no friend of pearls.)

    But if you do wash them, you can remove residual drilling dust by running a flexible wire needle with plain white cotton thread through the drill holes. Slide the pearl back and forth on the thread to remove the dust. I also do this to clean grime from just inside drill holes before restringing.
    Or if you have a silk cord with an attached needle, that will also work.

  4. #4
    First-graft Pearl Senior Guide Member
    Join Date
    Dec 2018
    Location
    Sydney
    Posts
    287

    Default

    I don’t have anything to add about cleaning but just wanted to comment on how lovely those strands look - I hope you’ll post photos when you receive them.

  5. #5
    Pearl Scholar Senior Pearl-Guide.com Pearl Expert pattye's Avatar
    Join Date
    Dec 2005
    Location
    Oregon
    Posts
    11,085

    Default

    I like that technique for cleaning also, PD.
    Pattye


    PatriciaSaabDesigns.etsy.com

    facebook.com/PatriciaSaabDesigns

    SO MANY PEARLS, SO LITTLE TIME----

Similar Threads

  1. How to Cut PowerPro for Clean Ends?
    By MSC in forum The Lowly Beaders' Club
    Replies: 7
    Last Post: 04-26-2016, 01:27 AM
  2. How to clean natural Abalone pearls
    By New Zealand Natural Pearl in forum Pearl Care & Cleaning
    Replies: 7
    Last Post: 02-24-2012, 06:29 PM
  3. How can I clean silver without damaging the pearls
    By Lotus99 in forum Pearl Care & Cleaning
    Replies: 2
    Last Post: 01-19-2012, 01:57 AM
  4. Sea Shells Used to Clean Up Heavy Metals
    By Mikeyy in forum Pearling Industry News
    Replies: 6
    Last Post: 04-28-2009, 10:26 PM
  5. Should I clean pearls before get them restrung?
    By want_to_buy_pearl in forum Pearl Care & Cleaning
    Replies: 5
    Last Post: 08-13-2006, 06:37 PM